Відео

Not one, static, profile shot of the shell on the bed... waste of a minute.

Thanking the person who made this video greatly. However, i would like to invite you looking into this method of tuning kingshocks 3.0 on gen2 raptor. I have done a great amount of offroading and onroad. Let me tell you what i think is another-easier way to tune king shocks with-out lifting your car or removing your tires. The method is basically opposite to the one in this video: 1- loosen the bolt just enough so you move the pin. 2- with-out holding the bolt, loosen the pin outward, meaning allowing full rebound or compression, in other words go to completely soft ( allowing the oil to move freely). 3- from completely soft adjust the pin to firmer, determine how much you want to restrict rebound or compressing, in other words how harsh-hard you want the shocks. 4- once you adjust the pin the desired turns. Now tighten the bolt down to fix pin in position. **Note from my experience using them harshly on offroad and onroad these are sweet spot for on road use that can take bumpy roads too: - rebound should be a turn or 2 higher ( firmer - stiffer) from compression. Because you want the tire to tuck in but return back to assure traction. - my current onroad setup with no load in the bed of the truck is so i made rebound and compression equal: Rear shocks ( from completely soft ) is Rebound short = completely open ( soft) Rebound long = 5 turns from completely open ( soft) Compression short = completely open ( soft) Compression long = 5 turns from completely open ( soft) Front ( from completely open - soft) = 6 clicks. You can tune your shocks from there to harsher depending on how fast, how much load you got on the truck's bed and your preference.

What’s the build list. I wanna do mine the same

My dad has not tried hells revenge yet he has only been on chickens corner and the new one, Dunes ( which we crashed in)

How come this never came out? King definitely should come out with an electronic controller like the SDI eclick, then they’d have the same as the fox live valve but even better

Interesting how you can independently control 3 different sets of lights with only two positives and 2 negatives connected.

Might as well wing it. Video is useless regarding the only important part: wiring.

Who knew you could spend 14 minutes telling people how to tighten and loosen adjusters without actually telling us any useful information on what it actually adjusts and how that changes the ride of the vehicle 😮

This guy :)

you can prime the oil system prior to starting a cold engine so you won't have phaser rattle noise

Omg That man's nails are disgusting

Thanks a lot for the info, I plan on buying a used gen 2 raptor and this eases my mind. I have done months of research and cam phasers seem to be the biggest conversation piece in all the forums so this info helps massively. Appreciate it man.

Hi there, I have a 2012 ford ranger 3.2. where can I order this BOV, with regards, Garry.

Would i be able to get these inlet tubes for California? Are rheir any inlet tubes that will pass CARB?

Would like details! What trim is this??

Great video and that is a sweet tatt

Here I am watching a real guy tune a real set of king shocks, just so I can turn around and tune my desert trucks in BeamNG.... God beams bypass physics have gotten insanely realistic.

just seeing this , do you all have the same setup for a 23 tacoma with the rack accessory?

The video is very helpful. Thank you. Can’t believe the tech mentions that it’s not a big deal. Puts me more at ease. I haven’t had issues but looking to budget for future problems. Anyone know how much the replacement should cost at a dealer or independent shop if they can do the work ?

For a 90k truck that is unacceptable.

More details of the build and longer bid, plz!

wow ! very detailed vid... definitely learned how to replace the ball joints . Thanks !

Why does everyone take the hub off the axle shaft? Just pull the whole thing out together.

Elpaso? 🧐

Hello from maui Hawaii! I recently bought a 2023 raptor and retired a 2014 f150 fx4 that had the 3.5 eco boost engine in it. The past truck was stock and it served me well. Stepping into the new raptor i have to say that it is a huge upgrade and I’m enjoying it immensely. One draw back that I’m feeling however is that on the 14’ truck i could hear the turbos pulling air and spinning up and in the new raptor I can’t. I realize the exhaust is louder but what i really want is that sound back. Not needing a blow off sound and so I’m wondering, since you installed the Cobb air intake and this boost tubes… does it bring back that swoosh fun turbo spool up noise?? Im not looking for power so much as the truck is already hard to keep below speed limits ( maui doesn’t even have one road thats over 60MPH). I love your videos and im sure in time I’ll put your wisdom to use in future upgrades. Thank you for your feedback!!!!

How do this compare to the mishimotos or AFE?

Oil doesn’t go in the turbo tubes, it goes back in to the inside of the intake manifold and that’s where you don’t want it to go back to (inside the engine) no oil should go back to the intake that’s what the catch can helps you prevent

Any chance this is the same for a Ram 2500 ? I can’t find decent directions on their site.

Outstanding!

I took out the hub assembly and axle shaft together in one piece. Works either way, just one less step on each side. Good vid.

Can we get the specs of this build?

is that C4 bumper?

I put the shim between the main plate and the bedliner like you did. Wondering if I should cut the bedliner so the shim is flat against the metal part of the bed? Any thoughts on this vs just pacing the shim over the hole on the bedliner?

Cool Tub

Gr8 video

Just purchased a used 2019 raptor with 30k, I’ll replace it thanks to your video.

Now in August 2023 , are the newest cam phasers FAILPROOF ?

Very good video. Just bought a 18 Raptor and have been curious about this issue. I don't believe that I have it on my new used raptor. Glad to hear that its really not that serious and from the research that I have done, this is an issue that is fixed after a one time service. Other than this issue, it's a very solid engine.

Solid

Thanks it is very help full , you doing great it take you 10 hrs. I am on the 10th day now trying to replace my ball joint.

The instructions from this company (GJ) are beyond awful.. they have instructions going up to 2018.. after that.. YOU'RE ON YOUR OWN!

Great job explaining and calling out the time consuming steps. This really helps us in allowing the appropriate time required.

i know this video is over three years old, however the presented information is very important and relevant in 2023. thank you.

How often should the Ignition Coil be changed? and the spark plugs?

@ 2:10 guy in the back looks like he just shit himself.

Did they fix your death wobble after ?

I have a question. Do you have to have a tapered cup to install the ball joints. I ordered a ball joint service kit from ebay and I don't see a tapered cup in it.the kit says it is for 2wd and 4wd so I didn't know if it wi work or not.

Did your BJ's show any visible signs of looseness with the tires on, or did you just assume so to fix the DW?

I've been trying to find little things that i can do to better performance on and off road, without breaking the bank.

Check engine light popped ip after installed…